Deutsch DTM



DTM Series Size 20 Contacts
2
3
4
2 size 20
3 size 20
4 size 20
6
8
12
6 size 20
8 size 20
12 size 20




MATERIAL SPECIFICATIONS
Plug/Receptacle
Shell:Thermoplastic
Wedge:Thermoplastic
Grommet:Silicone Rubber

Contacts
Pin:Copper Alloy
Socket:Copper Alloy
Finish:Nickel (optional - gold) Plated

Sealing Plugs
Thermoplastic: (All sizes)

GENERAL SPECIFICATIONS

Dielectric Withstanding Voltage
Current leakage less than 2 milliamps at 1500 VAC

Insulation Resistance:
1000 megohms minimum at 250 C.

Current Rating(Contact current rating @ 1250 C (continuous)
Size 20: 7.5 amps
Size 16: 13 amps
Size 12: 25 amps
Size 8: 60 amps
Size 4: 100 amps

Submersion:
Properly wired and mated connection will withstand immersion under three feet of water without loss of electronic qualities or leakage.

Fluid Resistance:
Connectors show no damage when exposed to most fluids used in industrial applications.

Vibration:
No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 G’s at 10 to 2000 Hz in each of the three mutually perpendicular planes. No electrical discontinuities longer than 1 microsecond.

Temperature:
Operative at temperatures from -550C to +1250C. Continuous at rated current.

Contact Retention:
Contacts withstand a minimum load of:
   20 lbs (89N) for size 20
   25 lbs (111N) for size 16
   30 lbs (133N) for size 12
   35 lbs (156N) for size 8
   35 lbs (156N) for size 4
Thermal Cycle:
No cracking, chipping or leaking after 20 test cycles from -550 C to +1250 C.


Durability:
No electrical or mechanical defects after 100 cycles of engagement and disengagement.


CONTACT RESISTANCE
CONTACT SIZE
WIRE GAUGE AWG(mm2)
Test Current(Amps)
Resistance (mV)Solids
Resistance (mV)Stamped & Formed
20
20(.50)
7.5
60
100
18(.80)
7.5
60
100
16(1.0)
7.5
60
100
16
20(.50)
7.5
60
100
18(.80)
10
60
100
16(1.0)
13
60
100
14 (2.0)
13
60
100
12
14(2.0)
18
60
100
12(3.0)
25
60
100
8
8(8.60)
60
60
N/A
10(.60)
60
60
N/A
4
6(13.0)
100
60
N/A


WIRE SEALING RANGE
CONTACT SIZE
RECOMMENDED WIRE INSULATION O.D.
N-SEAL
E-SEAL
#20
.053-.120
(1.35-3.05)
N/A
#16
.088-.145
(2.24-3.68)
.053-.120
(1.35-3.05)
#12
.134-.170
(3.40-4.32)
.097-.158
(2.46-4.01)
#8
.190-.240
(4.83-6.10)
N/A
#4
.280-.292
(7.11-7.42)
N/A


Environmentally-Sealed Transportation Connectors


Deutsch DTM Series
Deutsch DTM Series of transportation connectors feature a miniature contact with an enhanced design based on the world class, field-proven Deutsch DT Series.

The DTM is the connector to be used in harsh environmental application where reliable signal circuits are critical to operating performance. Typical applications include on or around the engine, the transmission and under the hood.


Features
Benefits
Integral Connector Latch Tactile and Audible Assembly Feedback
Rugged Thermoplastic Housing Field Proven Long Service Life
-55o C to +125o C Operating Temperature Engine Compartment Rated
Available Configurations:
  DTM/DT 2, 3, 4, 6, 8 & 12 - Size 20/16
  DTP 2 & 4 - Size 12
  DTHD 1 - Size 4, 8 & 12
Meets Most Harness Design Requirements
Silicone Seals: Superior Environmental Seal
  DTM: Accepts AWG 22 - 16 wire
  DT: Accepts AWG 20 - 14 wire
  DTP: Accepts AWG 14 - 10 wire
  DTHD: Accepts AWG 14 - 6 wire
Seals on .053” to .120 dia.(1.35mm to 3.05mm)
Seals on .053” to .145 dia.(1.35mm to 3.68 mm)
Seals on .097” to .170 dia.(2.46mm to 4.32mm)
Seals on .134 to .292 dia. (3.40mm to 7.42mm)
Crimp Contacts with Option of Gold or Nickel Finish, Solid or Stamped Construction Low Costs, High Reliability Terminals for Data & Signal Transmission
Current rating all contacts @ 1250 C no derating
  DTM - 7.5 Amps
  DT - 13 Amps
  DTP - 25 Amps
  DTHD - 25 to 100 Amps
Meets Most Signal Requirements
Fail-Safe Secondary Locks All (Except DTHD) Positive Contact Retention
Hand Insertable/Removable Contacts No Special Tools Required (Except DTHD)
Budget Minded Low Installation Costs


Product Line Overview

Deutsch DTM Series

Deutsch DTM Series of transportation connectors feature a miniature contact with an enhanced design based on the world class, field-proven Deutsch “DT Series”.

The DTM is the connector to be used in harsh environmental applications where reliable signal circuits are critical to operating performance. Typical applications include on or around the engine, the transmission and under the hood. In fact, everywhere data signals or critical electronic circuits go, the field proven Deutsch design of the DTM will provide reliable peak connector performance.

The low cost, size 20 contacts terminate AWG 16 to 22 gauge wire (0.5mm2 to 1.5mm2). Closed entry socket (female) contacts featuring spring action fingers are protected by a stainless steel hood. This allows for positive axial alignment while mating and prevents probe damage during testing.

Thermoplastic housings offer a wide operating temperature range (-550 C to +1250 C). Silicone rear wire and internal peripheral interface seals allow the DTM to withstand moisture and fluids.


PART NUMBERING SYSTEM(DTM)



Assembly Contact Insertion (DTM, DT, DTP)


1. Grasp crimped contact approximately 1.0” (25.4mm) behind the contact barrel.
2. Hold connector with rear grommet facing you.
3. Push contact straight into connector grommet until a click is felt. A slight tug will confirm that it is properly locked in place.


4. Once all contacts are in place, insert orange wedge: receptacles with half holes aligning with contacts. Plugs with contacts aligning behind full holes. The orange wedge will snap into place.

NOTE: The receptacle is shown use the same procedure for plug.


Contact Removal


1. Remove orange wedge using needlenose pliers to pull wedge straight out.
2. To remove the contacts, gently pull wire backwards, while at the same time releasing the locking finger by moving it away from the contact with a screwdriver.
3. Hold the rear seal in place, as removing the contact will displace the seal.

Sort By
WM-8S
Item Number: WM-8S
 
 
 



WM-8P
Item Number: WM-8P
 
 
 



WM-6S
Item Number: WM-6S
 
 
 



WM-6P
Item Number: WM-6P
 
 
 



WM-4S
Item Number: WM-4S
 
 
 



WM-4P
Item Number: WM-4P
 
 
 



WM-3S
Item Number: WM-3S
 
 
 



WM-3P
Item Number: WM-3P
 
 
 



WM-2S
Item Number: WM-2S
 
 
 



WM-2P
Item Number: WM-2P
 
 
 



WM-12S
Item Number: WM-12S
 
 
 



WM-12P
Item Number: WM-12P
 
 
 



DTM06-08SA-E007
Item Number: DTM06-08SA-E007
 
 
 



DTM06-6S-E007
Item Number: DTM06-6S-E007
 
 
 



DTM06-6S
Item Number: DTM06-6S
 
 
 



DTM06-4S-E007
Item Number: DTM06-4S-E007
 
 
 



DTM06-4S
Item Number: DTM06-4S
 
 
 



DTM06-3S-E007
Item Number: DTM06-3S-E007
 
 
 



DTM06-3S
Item Number: DTM06-3S
 
 
 



DTM06-2S-E007
Item Number: DTM06-2S-E007